Pertronix Distributor Wiring Diagram

Pertronix technical support () www. See figure “b” for wiring diagram.

Pertronix Flamethrower Distributor Wiring Diagram One Most

Pertronix Distributor Wiring Diagram. Connect the ignition switch wire directly to the ignitor black wire. Web follow the wiring diagrams that matches your applications. Web go to step 3.

Applications Which Use An External Ignition Box Should Use The Black Wire As The Trigger Wire.

Pertronix technical support () www. Diagramweb.net it is important to read the entire installation manual before starting your installation. This shows the proper hookup for a pertronix igniter in a car wired for negative ground, or earth if you prefer.

All Spark Plug Wires Should Be Seated Securely.

If you have a red wire and black wire, you have a negative ground ignitor. Do not use with solid ignition wires. I've confirmed the coil has adequate resistance, greater than 1.5 ohm across the poles when not connected.

Web The First Diagram Shows The Wiring For The Pertronix Ignitor, While The Other Two Diagrams Show The Wiring For The Resistor And Mounting Bracket.

Web whether you're looking for a custom tailored set or a kit to build wires to match your unique engine and wire loom configuration, we have the options. See figure “b” for wiring diagram. For installations that do not use a primary ballast resistor, connect the ignitor red wire to the positive (+) side of the ignition coil.

The Wiring Diagram Shown Below Is Modeled After One Obtained From Pertronix.

You may also choose to purchase a flamethrower 40,volt coil, which provides. Web there are two wires on all our distributors, one is red it goes to the + side of the coil. Place the magnet sleeve over the distributor shaft, and onto point cam.

Press Down Firmly To Insure Magnet Sleeve Is Fully Seated.

The ignitor does not require any modification to the distributor. We can set you up with 90°, 45°, or straight spark plug boot ends with both male. We recommend the factory spark plug heat range be used.

Magnet Sleeve Must Be Level With Ignitor Ii Module On Top.

Web advance curves this distributor is equipped with an advance curve that enables it to be used legally on vehicles outlined in the application guide. Web go to step 3. Jade bothma 1 min read.

Web Follow The Wiring Diagrams That Matches Your Applications.

It is factory set at 24° of centrifugal advance and includes silver advance springs. Tachometers should hook to the same location as stock. Web a pertronix flame thrower wiring diagram is a type of wiring diagram that is used specifically to connect electrical components in an automobile.

Counter Clockwise Distributors See Figure D.

Remove the ignition switch wire from the negative coil terminal. Web insert the ignitor black and red wires through the distributor housing verifying the grommet is seated properly. Ignitor™ common questions and answers figure 1 wiring diagram conventional points system with ballast resistor figure 2 wiring diagram ignitor system without ballast resistor figure 3 wiring diagram ignitor system.

Web Pertronix Igniter Wiring For Negative Ground Cars.

With the ignitor electronic ignition the ignition switch wire will no longer be connected to. If you have a black wire and black w/white tracer wire, you have a positive ground ignitor. Determine the type of tachometer you have and follow the.

Install The Ignitor Adapter Plate Over The Point Pivot Pin And Over The Eccentric Screw (Point Adjustment Screw), Rotate Eccentric Screw If Necessary To Properly Align Adapter Plate To Screw Hole On Breaker Plate.

Web 5 tach output (gray wire) 6 7 8 wiring diagram for ignitor, ii or iii distributor wiring diagram for wiring diagram for magnetic pickup distributor pertronix llc. It includes diagrams for various switches and circuits, as well as diagrams for various electrical components. Web #1 hello electrical gurus, i'm installing a pertronix ignitor (original, not ii or iii).

Web Logon To Www.pertronix.com For The Latest Technical Information.

Web to figure this out, a quick look at the two wires on the ignitor's is all that is needed. Make sure the source has power in both the start and run. Connect the ignition switch wire directly to the ignitor black wire.

You Want A Full 12V To The Coil + Side (No Ballast Resistor).

Mar 25, · pertronix has also sent me a diagram showing the correct wiring. This shows the proper hookup for a pertronix igniter in a car wired for negative ground, or earth if you prefer. Each diagram is labeled with the corresponding part and contains a legend to help you understand the symbols.

Clockwise Distributors See Figure C.

Web the wiring diagram shown below is modeled after one obtained from pertronix. Replace rotor and distributor cap. If it is a standard flame trower distributor, you want a 1.5 ohm coil like our flame thrower.

Do Not Disconnect Spark Plug Wires From Cap.

Web may 21, · finally finishing up the wiring on the '54 wagon and i ran unto a snag,,,i've lost the wiring diagram,,it's a flamethrower distributor with 2 wires and in my normal way of thinking the red wire is hot,,,but there is no red wire! The red wire should be connected to a 12v source controlled by the key.